4002 CAP PLATED SLOTTED

Dash Number	Total Panel Thickness	L	S	C	Part Number
-2	.051-.080	.413-.423	.69	.220	4002-2
-3	.081-.110	.443-.453	.72	.257	4002-3
-4	.111-.140	.473-.483	.75	.257	4002-4
-5	.141-.170	.503-.513	.78	.292	4002-5
-6	.171-200	.533-.543	.81	.322	4002-6
-7	.201-.230	.563-.573	.84	.352	4002-7
-8	.231-.260	.593-.603	.87	.382	4002-8

4002 STAINLESS STEEL SLOTTED

Dash Number	Total Panel Thickness	L	S	C	Part Num.
-2	.051-.080	.413-.423	.69	.220	4002-2S
-3	.081-.110	.443-.453	.72	.257	4002-3S
-4	.111-.140	.473-.483	.75	.257	4002-4S
-5	.141-.170	.503-.513	.78	.292	4002-5S
-6	.171-200	.533-.543	.81	.322	4002-6S
-7	.201-.230	.563-.573	.84	.352	4002-7S
-8	.231-.260	.593-.603	.87	.382	4002-8S
-9	.261-.290	.623-.633	.90	.412	4002-9S

4002 CAD PLATED PHILLIPS

Dash Number	Total Panel Thickness	L	S	C	Part Num.
-2	.051-.080	.413-.423	.69	.220	40S5-2
-3	.081-.110	.443-.453	.72	.257	40S5-3
-4	.111-.140	.473-.483	.75	.257	40S5-4
-5	.141-.170	.503-.513	.78	.292	40S5-5
-6	.171-200	.533-.543	.81	.322	40S5-6
-7	.201-.230	.563-.573	.84	.352	40S5-7
-8	.231-.260	.593-.603	.87	.382	40S5-8
-9	.261-.290	.623-.633	.90	.412	40S5-9

STAINLESS STEEL PHILLIPS

Dash Number	Total Panel Thickness	L	S	C	Part Num.
-2	.051-.080	.413-.423	.69	.220	40S5-2S
-3	.081-.110	.443-.453	.72	.257	40S5-3S
-4	.111-.140	.473-.483	.75	.257	40S5-4S
-5	.141-.170	.503-.513	.78	.292	40S5-5S
-6	.171-200	.533-.543	.81	.322	40S5-6S
-7	.201-.230	.563-.573	.84	.352	40S5-7S
-8	.231-.260	.593-.603	.87	.382	40S5-8S
-9	.261-.290	.623-.633	.90	.412	40S5-9S
-10	.291-.320	.653-.663	.93	.442	40S5-10S

CAD PLATED WING STUD

Dash Number	S	Part Num.
-2	.69	4002-2W
-3	.72	4002-3W
-4	.75	4002-4W
-5	.78	4002-5W
-6	.81	4002-6W
-8	.87	4002-8W
-9	.90	4002-9W
-10	.93	4002-10W
-11	.96	4002-11W
-12	.99	4002-12W

Q+A

Camlock grip thickness? How is this defined? Is this the thickness of the Panel that the stud is in plus the thickness of the panel that has the receptacle?
The grip for 4000 series studs is determined by the the grommet being used and both the stud & receptacle panel thicknesses. If you are using a flush grommet, the grip is just the two panel thicknesses, but if you are using a plus flush grommet, you need to add .054" for the 4002-N3, or .029" for the other plus flush grommets to get the grip thickness.